Up To Date

Diotec keeps its product portfolio close to the market demands with know-how, research and passion.


Want to do automatic assembly of the Bridge Rectifier to the PCB as well? Here is the solution! S16MSD2 - Half Bridge in D²PAK allows for full PCB assembled Power Rectifier Stages

data sheet s16asd2

When it comes to power bridge rectifiers, design engineers have to go back to through-hole devices which first need to be soldered onto the PCB, and then screwed to an extra heat-sink. These are manual assembly steps, which cost time and effort and also bear the risk of potential failures.

Other power semiconductors such as MOSFETs or IGBTs and diodes for the PFC, converter and inverter stage or brake chopper, are widely available in SMD outlines like the well known D²PAK. They can be assembled fully automatic by pick&place machines and afterwards solder process, at high speed and with constant quality.

The S16MSD2 half bridge closes the gap which was up to now at the input rectifier stage. Two of these parts form a full bridge, which can be assembled in the same process step than the other power semiconductors. Like for those, cooling is done via the PCB metallization. So the entire power stage can be done in one time and with the same concept.


  • Half bridge in SMD
  • Two parts build a full bridge
  • For fully automatic assembly
  • High power dissipation

Typical Applications

  • 50/60 Hz Mains Rectification
  • Power Supplies
  • Battery Chargers
  • Drive Inverters

DI6206 Series: Longer Operating Times for Battery-powered Electronics

Flyer DI6206 LDO Voltage Regulator

DI6206 Series from Diotec is a high precision CMOS based low drop out voltage regulator. The device is compatible with low ESR ceramic capacitors. It provides output currents over 200 mA and fixed output voltages of 1.5 V to 3.6 V from an input voltage of 7.0 V. Special features like very low quiescent current and low dropout voltage enables usage in low power applications, and allows for longer operation times of battery-powered electronics. Parts include additionally a current limit and short-circuit protection. For more information download our new LDO flyer.


  • Very Low Quiescent Current: typ. 1uA
  • Low Dropout Voltage: typ. 250 mV
  • Maximum Output current: 200mA
  • Output Voltage from 1.5V to 3.6V
  • Output Voltage Accuracy: ±1% and ±2%
  • Operating Temperature Range: -40°C to 85°C
  • Compatible with Low ESR Ceramic Capacitors
  • Built in Current Limiting Circuit

Typcial Applications:

  • Battery powered electronic devices
  • Mobile / Smart Phones
  • Digital Cameras and Camcorders
  • Home Automation Systems
  • Game Console

Powerful AC to DC Rectification on Printed Circuit Boards

data sheet gbu10a

The GBU10A...GBU10M series of single phase bridge rectifiers are offered in the GBU package with 5.08mm pitch. The devices can be operated free-standing for up to 7.0A of output current as well as clipped onto a heatsink for up to 10A. They are ideally suited for printed circuit board assemblies. With a case length of 21.5mm and a thickness of 3.4mm it can be used even in tight assemblies where space is restricted.


  • High forward surge current rating: 200A at 50Hz/10ms half sine wave pulse
  • Wide Reverse voltage range (Vrrm): 50V to 1000V
  • Low Forward voltage drop: < 1.0 V
  • High Isolation Voltage - terminal to case: > 1500 Vrms
  • Available in tubes for automatic assembly: Suffix -T

Typical Applications:

  • 50/60 Hz Mains Rectification
  • Power Supplies
  • Fans
  • SMPS
  • UPS
  • DC Drives

Watch our Technical Online Seminar hosted by IBS Electronics Group!

Video Webinar Diotec und IBS

If you missed our technical online seminar on May 7 hosted by our distributor IBS Electronics Group, you can re-watch it here.

This 45 minute online seminar presents innovative semiconductor solutions to maximize engineering efficiency through technical product introductions and the presentation of successful case studies. Learn more about Diotec’s technical advantages, manufacturing know how and semiconductor innovation.

Topics Include:

  • 3rd Gen Schottky Technology (-3G)
  • Linear Voltage Regulators
  • Avalanche Diodes
  • TVS Highlights
  • Melf, MiniMelf & SMA Package
  • TPSMA6L - TVS in Flat SMA
  • Power MOSFETs

Struggling with High Forward Voltage Drop at 60V Schottkys? We have the Solution!

data sheet sms560-3g

SMS560-3G is a 5A/60V Schottky offering a forward voltage drop which was only possible with 40V types up to now. It has less than 0.55V at 5A, and anyway, unlike other "low Vf" Schottky types a low reverse current of maximum 80µA at 60V.

This outstanding performance is realized by Diotec's 3rd generation chip technology. Compared to former generations, this is a reduction of almost 20% in forward drop and thus power losses. Junction temperature is further reduced by the thermally low resistive MELF package, where these parts are build in.

The SMS560-3G is ideal for polarity protection but also high power output rectification. The 40V type SMS540-3G with even lower Vf completes the product family.

Enhance Efficiency of your Design and Save Board Space at the Same Time

data sheet ER2DSMA

With the ER2DSMA, a 2A/200V Superfast Efficient Rectifier in SMA package designers can easily solve two of their typical challenges: Reducing board space on one side, and increasing power output on the other.

This high power density device features a forward voltage of less than 1V and a reverse recovery time below 35ns. This makes it ideally suited for switching frequencies in the 100kHz range. The device has similar performance compared to alternatives offered by other manufacturers in the bigger SMB package.

It is available both in commercial and Automotive grade (suffix -AQ), and is well suited for applications like high frequency inverters, DC/DC converters, freewheeling diodes and LED drivers.


  • Average Forward Current 2 A
  • Forward Voltage < 1.0 V
  • Reverse Recovery Time < 35ns
  • SMA Package
  • Repetitive Peak Reverse voltage 200 V
  • Leakage Current 5 µA
  • AEC-Q101 grade available

Need to Protect Your Sensitive Design and Space is Limited? Check Our Tiny Lead-less Packages!

Application Note ESD Protection Solutions

Our new Application Note ESD Protection Solutions introduces several so-called "lead-less" package outlines. Rather than having extended leads, these parts are connected on the bottom side and thus save valuable board space. Just one example out of several is the DI5315-02F in the very small SOT-883 or DFN1006-3 package.

It measures only 1.0mm by 0.6mm and offers two ESD protection diodes with common ground connection. They can protect high speed data lines and I/O ports, such as USB and HDMI interfaces, used at communication and entertainment devices.

New: Schottky in MiniMelf offers 2A of forward current at reduced reverse leakage

data sheet SGL2-40-3G

The SGL2-40-3G is a 2A/40V Schottky in the small yet powerful MiniMelf package. It uses the 3rd Generation chip technology offering a forward voltage drop of less than 530mV at 2A and a reverse leakage of below 40µA at 40V. Thus these parts are ideally suited for baterry charging circuits, where a high forward current is required for fast charging and low reverse leakage for a low discharging rate.

Further applications include the output rectification in AC/DC and DC/DC converters, polarity protection and free-wheeling diodes. The advantages of the MiniMelf case outline (DO-213AA) over lead-frame versions are explained in this short video.

New: 3A Rectifier Bridge in KBP Package

data sheet kbp302g

The KBP302G...KBP310G series of bridge rectifiers are offered in the small inline package KBP with 4mm pitch. The devices can be operated free-standing for up to 1.8A of output current as well as clipped onto a heatsink for up to 3A.

Forward surge current rating is 65A at 50Hz/10ms half sine wave pulse, the reverse voltage Vrrm ranges from 200V to 1000V. With a case length of 14.5mm and a thickness of 3.5mm it can be used even in tight assemblies where space is restricted.

TPSMA6L Series - Discover our new 600W TVS in a Flat SMA package

data sheet TPSMA6L

Diotec introduces the new 600W transient voltage suppressors TPSMA6L in a Flat SMA Package, featuring a typical height of 1.3mm only. It features a peak pulse power of 600W at 10/1000µs pulse form. Reverse stand-off voltage ranges from 5.0V to 85V.

The TPSMA6L are a cost effective solution having the same level of peak pulse power like the bigger P6SMBJ series. The flat SMA version offers a foot print size reduction of around 33% when compared to the SMB package and 45% less height when compared to both SMA and SMB packages.

Features and benefits are:

  • High power density
  • Smaller dimensions and low height profile package for space saving
  • Pad layout compatible with SMA packages

Parts are typically used in these applications:

  • Over-voltage protection
  • ESD protection
  • Free-wheeling diodes